Skip to main content

Fibre Optic Installation

End-to-end fibre optic solutions

Whether you are future-proofing the network for your business, data centre or large-scale infrastructure, our team delivers tailored fibre optic installation to keep you connected.

Priced
Quoted per job
Fibre
OM3/OM4, OS1/OS2, SWA
Splicing
Fujikura core alignment
Coverage
Herts, Essex, London

What is fibre optic installation?

Dig IT Solutions designs and installs fibre optic links for businesses, data centres and large-scale sites across Hertfordshire, Essex and London: OM3 and OM4 multimode between cabinets, OS1 and OS2 single mode for GPON infrastructure and long runs, and SWA armoured fibre where the cable needs extra protection. We install direct buried, across-site and in-building routes, and terminate by direct termination (hot melt and cold cure) or fusion splicing using the latest Fujikura core alignment splicers.

Problems we fix

The problems this service exists to solve

  1. 01

    A second building on an unreliable link

    Another building, unit or site that needs connecting, and a wireless bridge or long copper run that isn't reliable enough.

  2. 02

    Copper at its limit between floors

    Cabinets on different floors or at opposite ends of a building linked by copper that can't give the distance or bandwidth you need.

  3. 03

    Long runs and the wrong spec

    A run of over 500 metres, or GPON infrastructure, where specifying the wrong fibre means it has to be done twice.

  4. 04

    Routes that need protecting

    Cable that has to go underground or across an open site, where unprotected fibre would be crushed, cut or chewed.

Scope

What is included

Every fibre job is specified and quoted individually. Whichever route it takes, the scope covers the fibre itself, the protection it needs and how it is terminated.
  • 01

    Fibre specified for the job

    Distance, bandwidth, route and environment decide the fibre: multimode for shorter high-speed links, single mode where you need to travel over 500 metres or run GPON, and armoured cable where the route demands it.

  • 02

    OM3 and OM4 multimode

    Multimode links for your cabinets, comms rooms and data centre racks, and backbones between floors.

  • 03

    OS1 and OS2 single mode

    Single mode fibre for GPON infrastructure, long runs and links between buildings across a site.

  • 04

    SWA armoured and direct buried fibre

    Steel wire armoured cable for direct burial, across-site runs and anywhere the fibre needs extra mechanical protection.

  • 05

    Building-to-building and floor-to-floor links

    Whether you have multiple buildings to connect or just need to connect between floors, routes are planned through the site and building infrastructure before work starts.

  • 06

    Termination and fusion splicing

    Direct termination using hot melt and cold cure connectors, or fusion splicing with the latest Fujikura core alignment splicers, depending on the link and the location.

Process

How it starts

  1. 01

    Call for a quotation

    Tell us what needs connecting: the buildings, floors or cabinets, roughly how far apart they are and what the link is for.

  2. 02

    Route and specification

    We plan the route, whether buried, across site or inside the building, and specify the fibre type, core count and protection.

  3. 03

    Installation

    The fibre is installed along the agreed route, armoured or ducted where it needs to be.

  4. 04

    Termination and splicing

    Each end is terminated by hot melt, cold cure or Fujikura fusion splicing, ready for the network equipment.

Outcomes

What changes for the business

  • The right fibre for the distance, not over- or under-specified
  • Buildings and floors linked by fibre rather than copper or a wireless bridge
  • Cable protected for burial and open-site routes
  • One team for the fibre, the network on top of it and the support afterwards

FAQ

Questions we are asked

Straight answers. If yours is not here, call 020 8482 4020 or 01992 939 365 and ask an engineer.
What is the difference between multimode and single mode fibre?
Multimode fibre (OM3 and OM4) has a wider core and is used for shorter, high-bandwidth links, such as between cabinets in a comms room or data centre, or between floors. Single mode fibre (OS1 and OS2) has a much narrower core and carries signals far further, so it is the choice for runs over 500 metres, links between buildings across a site and GPON infrastructure. OS1 is typically used indoors and OS2 for longer and external runs.
Do we need armoured fibre?
If the cable is direct buried, crosses an open site or runs anywhere it could be crushed, cut or chewed, steel wire armoured (SWA) fibre gives it that extra protection. Fibre inside a building, in trunking or containment, usually does not need armour. We recommend the cable construction after looking at the route.
What is fusion splicing, and when do you use direct termination?
Fusion splicing joins two fibres permanently by welding them with an electric arc. We use the latest Fujikura core alignment splicers, which line up the fibre cores themselves rather than the outer cladding, for a consistently low-loss joint. Direct termination fits a connector straight onto the fibre using either hot melt (a heat-cured adhesive) or cold cure (an adhesive that sets without heat). Which method we use depends on the fibre type, the number of cores and where the termination is.
Can you run fibre between buildings or underground?
Yes. Dig IT Solutions is experienced in direct buried fibre, across-site fibre runs and building infrastructure. Whether you have multiple buildings to connect or just need to connect between floors, we plan the route, specify the fibre and protection it needs, and install and terminate it.
Do you also install the network that runs over the fibre?
Yes. The same team designs and installs the switching, firewalls and Wi-Fi that sit on top of the fibre, and can monitor and support the network afterwards. Read more about IT infrastructure and networking and structured cabling.
How much does fibre optic installation cost?
Every fibre job is quoted individually, because the cost depends on the distance, the route (buried, across site or inside the building), the fibre type and core count, whether armour is needed and how it is terminated. Feel free to call us on 020 8482 4020 for a quotation, or send the details through the contact page.

Next step

Talk to an engineer, not a sales script

Tell us what is not working, or what you are planning, and we will give you a straight view on what it would take to fix.

WhatsApp us